|
|
ARCHIVE page 1 of 4
 |
 |
|
AMPER EXHIBITION - PRAGUE 27.-30.3.2007 |
|
Our booth C22 was situated in the hall 4. New RFID products were presented including practical demonstrations of communication between readers and different kinds of RFID tags:
• EM4095 - RFID Reader 125kHz
• EM4094 - RFID Reader 13.56MHz
• EM4294 - 13.56MHz Crypto Analogue Front End Circuit for High Secure RFID communication
• UHF RFID demo kit with EM4298, new iP-X, ISO 18000-6A/B & C compliant UHF Decoder / Encoder
Beside RFID you were faced with new experience of our designers by means of the examples of brand new finished projects.
In the second part of our booth we demonstrated SW solutions for PCB, HDL and harness designs of the Mentor Graphics company, the EDA technology leader. ASICentrum is a Mentor Graphics distributor for the Czech and Slovak Republics providing also SW support and training services.
THANK YOU FOR YOUR VISIT IN OUR BOOTH. |
|
| http://www.amper.cz/en/ |
|
|
 |
|
|
|
EM6110 - LCD CONTROLLER AND DRIVER FOR LOW MULTIPLEX RATES AND STATIC |
|
Universal LCD controller and driver for full dot-matrix monochrome TN and STN LCD displays.
• 3-wire or I2C serial interface
• large voltage range (1.8V to 5.5V for logic and 3V to 10V for LCD)
• programmable 8, 4, 3, 2 and 1 row modes
• all segments or Display ON and OFF functions
• shift register function
• low operating current consumption
• embedded functions (oscillator, bias resistors, synchronisation)
• no additional external components |
|
| http://www.emmicroelectronic.com/Products.asp?IdProduct=243 |
|
|
|
|
|
|
The IEEE Workshop DDECS 2006 in Prague |
|
ASICentrum belonged to the sponsors of DDECS, the 9th IEEE International Workshop on Design & Diagnostics of Electronic Circuits & Systems. The workshop site was the Congress Center of the Czech Technical University called "Masarykova kolej", Thákurova 1, Prague 6, Czech Republic in April 18.-21, 2006.
Topics of interest included ASIC/FPGA Design, Bio-inspired Hardware, Design Verification/Validation, Hardware/Software Co-Design, Reconfigurable Computing, System-on-a-Chip (SoC), Analog, Mixed-Signal, and RF Test, Design for Testability and Diagnosis, Defect/Fault Tolerance and Reliability, Memory and Processor Test, MEMS Testing and many other. |
|
| http://ddecs06.felk.cvut.cz/ |
|
|
|
|
|
|
EM4094 - 13.56MHz, compliant ISO 15693 and ISO 14443A&B, Analog Front End IC for RFID Base Station |
|
• Oscillator using 13.56MHz Quartz with selectable transconductance.
• High output power 200mW from 5V supply
• AM/PM demodulation with AGC signal amplifier
• 848KHz BPSK internal decoder (type B)
• Multiple sub-carrier receiving compatibility (212kHz, 424kHz and 848kHz)
• Multiple sub-carrier coding compatibility (Manchester, BPSK)
• Selectable receive gain
• Serial 3 pin interface for option selection
• Power down mode controlled by the 3 wires SPI
• Operation temperature range -40°C to +85°C |
|
| http://www.emmicroelectronic.com/DetailNews.asp?IdNews=96 |
|
|
|
|
|
|
EM6152 - Automotive Regulator with Windowed Watchdog |
|
• Low quiescent current 135 uA
• -40°C to +125°C temperature range
• Highly accurate 5 V, 400 mA guaranteed output (actual maximum current depends on power dissipation)
• Low dropout voltage, typically 250 mV at 250 mA
• Unregulated DC input can withstand -42 V reverse battery and +45 V power transients
• Fully operational for unregulated DC input voltage up to 40 V and regulated output voltage down to 3.0 V
• No reverse output current
• Very low temperature coefficient for the regulated output
• Windowed watchdog with an adjustable time windows, guaranteeing a min time and max time between software clearing of the watchdog
• Qualified according to AEC-Q100 |
|
| http://www.emmicroelectronic.com/Products.asp?IdProduct=231 |
|
|
|
|
|
|
EM6151 - Windowed Watchdog IC with Enhanced System Security |
|
|
EM Microelectronic introduces the EM6151, a highly-integrated microprocessor voltage supervisory IC with programmable reset threshold voltages and a watchdog timer with programmable time window and system enable output. For maximum flexibility, this circuit is available in several versions, allowing for different ratios of the opened/closed window of the watchdog and power saving function compatible with CAN-bus sleep mode. The EM6151 features an open drain reset output, comes in a compact 8-pin SO8 package and operates over the temperature range from -40 to +125 °C, making it compatible with the demanding temperature extremes in automotive and industrial environments. A low power product, EM6151 draws only 35uA quiescent current. |
|
| http://www.emmicroelectronic.com/Products.asp?IdProduct=229 |
|
|
|
|
|
|
First smart card IC allowing flexible memory partitioning between code and data |
|
EMTCG176-3G is a unique flash memory-based smart card IC designed for use in SIM and Java cards for GSM mobile phones, as well as for healthcare and loyalty card applications. The EMTCG176-3G is compatible with the ISO7816-3 Integrated Circuit Card (smart card) specification, and operates with high speed communication baud rates, making it compatible with the 3rd generation of cellular telephones.
• Fast 8051 software compatible MCU with a x3 acceleration factor
• 128 KB FLASH GP NVM of high secured area (512 Bytes/block)
• 48 KB EEPROM, 3.3 KB RAM
• True Random Number Generator FIPS140-2 compliant
• Cryptography (3xDES)
• DPA resistance
• Unique ID per chip |
|
| http://www.emmicroelectronic.com/DetailNews.asp?IdNews=88 |
|
|
|
|
|
|
EM4026 - RFID CIRCUIT HITS THE SKI SLOPES |
|
EM Microelectronic, an electronic systems company of the Swatch Group and the world’s largest supplier of RFID ICs, has developed in cooperation with Skidata and EC-Passage a transponder chip, the EM4026, which greatly facilitates the handling and identification of rented skis or snowboards in ski resorts.
• Implements free-running anti-collision protocol with FAST SWITCH-OFF and SLOW-DOWN modes
• Ability to identify a number of transponders higher than 100 (FAST MODE)
• Factory programmed 64-bit ID number
• Operating field frequency: 125 kHz
• No external supply buffer capacitor needed
• Pad size for direct bonding 200 x 400 mm (bump)
• -40 to +85°C operating temperature |
|
| http://www.emmicroelectronic.com/Products.asp?IdProduct=222 |
|
|
|
|
|
|
|
 |
